/[MITgcm]/manual/s_phys_pkgs/text/obcs.tex

Diff of /manual/s_phys_pkgs/text/obcs.tex

Parent Directory | Revision Log | View Revision Graph Revision Graph | View Patch Patch

-revision 1.6 by mlosch,
Fri Feb 25 17:26:17 2011 UTC
+revision 1.13 by mlosch,
Mon May  2 09:11:20 2011 UTC
 Line 11 
 Alistair Adcroft, Patrick Heimbach, Sama
  \subsubsection{Introduction
  \label{sec:pkg:obcs:intro}}
+ The OBCS-package is fundamental to regional ocean modelling with the
+ MITgcm, but there are so many details to be considered in
+ regional ocean modelling that this package cannot accomodate all
+ imaginable and possible options. Therefore, for a regional simulation
+ with very particular details, it is recommended to familiarize oneself
+ not only with the compile- and runtime-options of this package, but
+ also with the code itself. In many cases it will be necessary to adapt
+ the obcs-code (in particular \code{S/R OBCS\_CALC}) to the application
+ in question; in these cases the obcs-package (together with the
+ rbcs-package, section \ref{sec:pkg:rbcs}) is a very
+ useful infrastructure for implementing special regional models.
  %----------------------------------------------------------------------
-Line 95 
 Run-time parameters are set in files
+Line 105 
 Run-time parameters are set in files
  \code{data.pkg}, \code{data.obcs}, and \code{data.exf}
  if ``real-time'' prescription is requested
  (i.e. package \code{exf} enabled).
- These parameter files are read in S/R
+ vThese parameter files are read in S/R
  \code{packages\_readparms.F}, \code{obcs\_readparms.F}, and
  \code{exf\_readparms.F}, respectively.
  Run-time parameters may be broken into 3 categories:
-Line 143 
 their default values.
+Line 153 
 their default values.
             ~ \\
          useOBCSbalance & \code{.FALSE.} &
             ~ \\
+            OBCS\_balanceFacN/S/E/W & 1 & factor(s) determining the details
+            of the balaning code \\
          useOrlanskiNorth/South/EastWest & \code{.FALSE.} &
             turn on Orlanski boundary conditions for individual boundary\\
          useStevensNorth/South/EastWest & \code{.FALSE.} &
-Line 232 
 A zero (0) element in $\tt OB\_I\ldots$,
+Line 244 
 A zero (0) element in $\tt OB\_I\ldots$,
  means there is no corresponding OB in that column/row.
  For a Northern/Southern OB, the OB V point is to the South/North.
  For an Eastern/Western OB, the OB U point is to the West/East.
+ For example,
- \begin{verbatim}
+ \begin{tabbing}
-  For example
+   \code{OB\_Jnorth(3)=34} \=  means that:  \= \\
-      OB_Jnorth(3)=34  means that:
+   \> \code{T(3,34)} \> is a an OB point  \\
-           T( 3 ,34) is a an OB point
+   \> \code{U(3,34)} \> is a an OB point \\
-           U(3:4,34) is a an OB point
+   \> \code{V(3,34)} \> is a an OB point \\
-           V( 4 ,34) is a an OB point
+   \code{OB\_Jsouth(3)=1} \> means that: \\
-  while
+   \> \code{T(3,1)} \> is a an OB point \\
-      OB_Jsouth(3)=1  means that:
+   \> \code{U(3,1)} \> is a an OB point \\
-           T( 3 ,1) is a an OB point
+   \> \code{V(3,2)} \> is a an OB point \\
-           U(3:4,1) is a an OB point
+   \code{OB\_Ieast(10)=69} \>  means that:  \>  \\
-           V( 4 ,2) is a an OB point
+   \> \code{T(69,10)} \> is a an OB point \\
- \end{verbatim}
+   \> \code{U(69,10)} \> is a an OB point \\
+   \> \code{V(69,10)} \> is a an OB point \\
- For convenience, negative values for Jnorth/Ieast refer to
+   \code{OB\_Iwest(10)=1} \>  means that:  \>  \\
+   \> \code{T(1,10)} \> is a an OB point \\
+   \> \code{U(2,10)} \> is a an OB point \\
+   \> \code{V(1,10)} \> is a an OB point
+ \end{tabbing}
+ For convenience, negative values for \code{Jnorth}/\code{Ieast} refer to
  points relative to the Northern/Eastern edges of the model
  eg. $\tt OB\_Jnorth(3)=-1$  means that the point $\tt (3,Ny)$
  is a northern OB.
-Line 291 
 prescribed time-constant or time-varying
+Line 308 
 prescribed time-constant or time-varying
  use prescribed boundary fields to compute Stevens boundary conditions.
  \end{itemize}
  \paragraph{ORLANSKI:} ~ \\
  %
  Orlanski radiation conditions \citep{orl:76}, examples can be found in
-Line 317 
 open boundary:
+Line 333 
 open boundary:
  \item If non-hydrostatic dynamics are used
    (\ref{sec:non-hydrostatic}), additional files
    \code{OB[N/S/E/W]wFile} for the vertical velocity $w$ with
-   dimensions $(N_{x/y}\times N_r\times\mbox{time levels})$ may be
+   dimensions $(N_{x/y}\times N_r\times\mbox{time levels})$ can be
    specified.
  \item If \code{useSEAICE=.TRUE.} then additional files
    \code{OB[N/S/E/W][a,h,sl,sn,uice,vice]} for sea ice area, thickness
    (\code{HEFF}), seaice salinity, snow and ice velocities
-   $(N_{x/y}\times\mbox{time levels})$ may be specified.
+   $(N_{x/y}\times\mbox{time levels})$ can be specified.
  \end{itemize}
- When the \code{exf}-package is used, the time levels are controlled
+ As in \code{S/R external\_fields\_load} or the \code{exf}-package, the
- for each boundary separately in the same way as the \code{exf}-fields
+ code reads two time levels for each variable, e.g.\ \code{OBNu0} and
- in \code{data.exf}, namelist \code{EXF\_NML\_OBCS}. The runtime flags
+ \code{OBNu1}, and interpolates linearly between these time levels to
+ obtain the value \code{OBNu} at the current model time (step). When the
+ \code{exf}-package is used, the time levels are controlled for each
+ boundary separately in the same way as the \code{exf}-fields in
+ \code{data.exf}, namelist \code{EXF\_NML\_OBCS}. The runtime flags
  follow the above naming conventions, e.g. for the western boundary the
  corresponding flags are \code{OBCWstartdate1/2} and
  \code{OBCWperiod}. Sea-ice boundary values are controlled separately
- with \code{siobWstartdate1/2} and \code{siobWperiod}.
+ with \code{siobWstartdate1/2} and \code{siobWperiod}.  When the
- When the \code{exf}-package is not used, the time levels are
+ \code{exf}-package is not used, the time levels are controlled by the
- controlled by the runtime flags \code{externForcingPeriod} and
+ runtime flags \code{externForcingPeriod} and \code{externForcingCycle}
- \code{externForcingCycle} in \code{data}, see \code{verification/exp4}
+ in \code{data}, see \code{verification/exp4} for an example.
- for an example.
  \paragraph{OBCS\_CALC\_STEVENS:} ~ \\
  (THE IMPLEMENTATION OF THESE BOUNDARY CONDITIONS IS NOT COMPLETE. SO
-Line 345 
 function along the open boundary) $\bar{
+Line 364 
 function along the open boundary) $\bar{
  $\chi_{ob}$ (note: passive tracers are currently not implemented and
  the code stops when package \code{ptracers} is used together with this
  option). Currently, the code vertically averages the normal velocity
- as specified. From these prescribed values the code computes the
+ as specified in \code{OB[E,W]u} or \code{OB[N,S]v}. From these
- boundary values for the next timestep $n+1$ as follows (as an
+ prescribed values the code computes the boundary values for the next
- example, we use the notation for an eastern or western boundary):
+ timestep $n+1$ as follows (as an example, we use the notation for an
+ eastern or western boundary):
  \begin{itemize}
- \item $u^{n+1}(y,z) = \bar{u}_{ob}(y) + u'(y,z)$, where $u_{n}'$ is the
+ \item $u^{n+1}(y,z) = \bar{u}_{ob}(y) + (u')^{n}(y,z)$, where $(u')^{n}$
-   deviation from the vertically averaged velocity one grid point
+   is the deviation from the vertically averaged velocity at timestep
-   inward from the boundary.
+   $n$ one grid point inward from the boundary.
  \item If $u^{n+1}$ is directed into the model domain, the boudary
    value for tracer $\chi$ is restored to the prescribed values:
    \[\chi^{n+1} =   \chi^{n} + \frac{\Delta{t}}{\tau_\chi} (\chi_{ob} -
    \chi^{n}),\] where $\tau_\chi$ is the relaxation time
-   scale \texttt{T/SrelaxStevens}.
+   scale \texttt{T/SrelaxStevens}. The new $\chi^{n+1}$ is then subject
- \item If $u^{n+1}$ is directed out of the model domain, the tracer is
+   to the advection by $u^{n+1}$.
-   advected out of the domain with $u^{n+1}+c$, where $c$ is a phase
+ \item If $u^{n+1}$ is directed out of the model domain, the tracer
-   velocity estimated as
+   $\chi^{n+1}$ on the boundary at timestep $n+1$ is estimated from
-   $\frac{1}{2}\frac{\partial\chi}{\partial{t}}/\frac{\partial\chi}{\partial{x}}$.
+   advection advected out of the domain with $u^{n+1}+c$, where $c$ is
+   a phase velocity estimated as
+   $\frac{1}{2}\frac{\partial\chi}{\partial{t}}/\frac{\partial\chi}{\partial{x}}$. The
+   numerical scheme is (as an example for an eastern boundary):
+   \[\chi_{i_{b},j,k}^{n+1} =   \chi_{i_{b},j,k}^{n} + \Delta{t}
+   (u^{n+1}+c)_{i_{b},j,k}\frac{\chi_{i_{b},j,k}^{n}
+     - \chi_{i_{b}-1,j,k}^{n}}{\Delta{x}_{i_{b},j}^{C}}\mbox{, if }u_{i_{b},j,k}^{n+1}>0,
+   \] where $i_{b}$ is the boundary index.
    For test purposes, the phase velocity contribution or the entire
-   advection can
+   advection can be turned off by setting the corresponding parameters
-   be turned off by setting the corresponding parameters
    \texttt{useStevensPhaseVel} and \texttt{useStevensAdvection} to
    \texttt{.FALSE.}.\end{itemize} See \citet{stevens:90} for details.
- \paragraph{OBCS\_BALANCE} ~ \\
+ \paragraph{OBCS\_BALANCE\_FLOW:} ~ \\
  %
- ~
+ When turned on (\code{ALLOW\_OBCS\_BALANCE}
+ defined in \code{OBCS\_OPTIONS.h} and \code{useOBCSbalance=.true.} in
+ \code{data.obcs/OBCS\_PARM01}), this routine balances the net flow
+ across the open boundaries. By default the net flow across the
+ boundaries is computed and all normal velocities on boundaries are
+ adjusted to obtain zero net inflow.
+ This behavior can be controlled with the runtime flags
+ \code{OBCS\_balanceFacN/S/E/W}. The values of these flags determine
+ how the net inflow is redistributed as small correction velocities
+ between the individual sections. A value ``\code{-1}'' balances an
+ individual boundary, values $>0$ determine the relative size of the
+ correction. For example, the values
+ \begin{tabbing}
+  \code{OBCS\_balanceFacE}\code{ = 1.,} \\
+  \code{OBCS\_balanceFacW}\code{ = -1.,} \\
+  \code{OBCS\_balanceFacN}\code{ = 2.,} \\
+  \code{OBCS\_balanceFacS}\code{ = 0.,}
+ \end{tabbing}
+ make the model
+ \begin{itemize}
+ \item correct Western \code{OBWu} by substracting a uniform velocity to
+ ensure zero net transport through the Western open boundary;
+ \item correct Eastern and Northern normal flow, with the Northern
+   velocity correction two times larger than the Eastern correction, but
+   \emph{not} the Southern normal flow, to ensure that the total inflow through
+   East, Northern, and Southern open boundary is balanced.
+ \end{itemize}
+ The old method of balancing the net flow for all sections individually
+ can be recovered by setting all flags to -1. Then the normal
+ velocities across each of the four boundaries are modified separately,
+ so that the net volume transport across \emph{each} boundary is
+ zero. For example, for the western boundary at $i=i_{b}$, the modified
+ velocity is:
+ \[
+ u(y,z) - \int_{\mbox{western boundary}}u\,dy\,dz \approx OBNu(j,k) - \sum_{j,k}
+ OBNu(j,k) h_{w}(i_{b},j,k)\Delta{y_G(i_{b},j)}\Delta{z(k)}.
+ \]
+ This also ensures a net total inflow of zero through all boundaries,
+ but this combination of flags is \emph{not} useful if you want to
+ simulate, say, a sector of the Southern Ocean with a strong ACC
+ entering through the western and leaving through the eastern boundary,
+ because the value of ``\code{-1}'' for these flags will make sure that
+ the strong inflow is removed. Clearly, gobal balancing with
+ \code{OBCS\_balanceFacE/W/N/S} $\ge0$ is the preferred method.
  \paragraph{OBCS\_APPLY\_*:} ~ \\
  ~
- \paragraph{OBCS\_SPONGE} Setting sponge layer characteristics \\
+ \paragraph{OBCS\_SPONGE:} ~ \\
  %
- ~
+ The sponge layer code (turned on with \code{ALLOW\_OBCS\_SPONGE} and
+ \code{useOBCSsponge}) adds a relaxation term to the right-hand-side of
+ the momentum and tracer equations. The variables are relaxed towards
+ the boundary values with a relaxation time scale that increases
+ linearly with distance from the boundary
+ \[
+ G_{\chi}^{\mbox{(sponge)}} =
+ - \frac{\chi - [( L - \delta{L} ) \chi_{BC} + \delta{L}\chi]/L}
+ {[(L-\delta{L})\tau_{b}+\delta{L}\tau_{i}]/L}
+ = - \frac{\chi - [( 1 - l ) \chi_{BC} + l\chi]}
+ {[(1-l)\tau_{b}+l\tau_{i}]}
+ \]
+ where $\chi$ is the model variable (U/V/T/S) in the interior,
+ $\chi_{BC}$ the boundary value, $L$ the thickness of the sponge layer
+ (runtime parameter \code{spongeThickness} in number of grid points),
+ $\delta{L}\in[0,L]$ ($\frac{\delta{L}}{L}=l\in[0,1]$) the distance from the boundary (also in grid points), and
+ $\tau_{b}$ (runtime parameters \code{Urelaxobcsbound} and
+ \code{Vrelaxobcsbound}) and $\tau_{i}$ (runtime parameters
+ \code{Urelaxobcsinner} and \code{Vrelaxobcsinner}) the relaxation time
+ scales on the boundary and at the interior termination of the sponge
+ layer. The parameters \code{Urelaxobcsbound/inner} set the relaxation
+ time scales for the Eastern and Western boundaries,
+ \code{Vrelaxobcsbound/inner} for the Northern and Southern boundaries.
  \paragraph{OB's with nonlinear free surface} ~ \\
  %
-Line 425 
 Table \ref{tab:pkg:obcs:diagnostics}.
+Line 519 
 Table \ref{tab:pkg:obcs:diagnostics}.
  %----------------------------------------------------------------------
  \subsubsection{Reference experiments}
+ In the directory \code{verifcation}, the following experiments use
+ \code{obcs}:
+ \begin{itemize}
+ \item \code{exp4}: box with 4 open boundaries, simulating flow over a
+   Gaussian bump based on \citet{adcroft:97}, also tests
+   Stevens-boundary conditions;
+ \item \code{dome}: based on the project ``Dynamics of Overflow Mixing
+   and Entrainment''
+   (\url{http://www.rsmas.miami.edu/personal/tamay/DOME/dome.html}), uses
+   Orlanski-BCs;
+ \item \code{internal\_wave}: uses a heavily modified \code{S/R~OBCS\_CALC}
+ \item \code{seaice\_obcs}: simple example who to use the sea-ice
+   related code, based on \code{lab\_sea};
+ \item \code{tutorial\_plume\_on\_slope}: uses Orlanski-BCs, see also
+   section~\ref{sec:eg-gravityplume}.
+ \end{itemize}
-Line 436 
 Table \ref{tab:pkg:obcs:diagnostics}.
+Line 546 
 Table \ref{tab:pkg:obcs:diagnostics}.
  \label{sec:pkg:obcs:experiments}
  \begin{itemize}
- \item{Ocean experiment in exp4 verification directory. }
+ \item \code{tutorial\_plume\_on\_slope} (section~\ref{sec:eg-gravityplume})
  \end{itemize}

 Legend:



Removed from v.1.6
 


changed lines


 
Added in v.1.13
 Legend:



Removed from v.1.6
 


changed lines


 
Added in v.1.13
-Removed from v.1.6
+Added in v.1.13

	ViewVC Help
Powered by ViewVC 1.1.22