| 1 |
molod |
1.4 |
\subsection{Gridalt - Alternate Grid Package} |
| 2 |
edhill |
1.2 |
\label{sec:pkg:gridalt} |
| 3 |
|
|
\begin{rawhtml} |
| 4 |
|
|
<!-- CMIREDIR:package_gridalt: --> |
| 5 |
|
|
\end{rawhtml} |
| 6 |
molod |
1.1 |
|
| 7 |
molod |
1.4 |
\subsubsection {Introduction} |
| 8 |
molod |
1.1 |
|
| 9 |
jmc |
1.12 |
The gridalt package \citep{mol:09} |
| 10 |
|
|
is designed to allow different components of MITgcm to |
| 11 |
molod |
1.5 |
be run using horizontal and/or vertical grids which are different from the main |
| 12 |
|
|
model grid. The gridalt routines handle the definition of the all the various |
| 13 |
|
|
alternative grid(s) and the mappings between them and the MITgcm grid. |
| 14 |
|
|
The implementation of the gridalt package which allows the high end atmospheric |
| 15 |
|
|
physics (fizhi) to be run on a high resolution and quasi terrain-following vertical |
| 16 |
|
|
grid is documented here. The package has also (with some user modifications) been used |
| 17 |
|
|
for other calculations within the GCM. |
| 18 |
|
|
|
| 19 |
|
|
The rationale for implementing the atmospheric physics on a high resolution vertical |
| 20 |
|
|
grid involves the fact that the MITgcm $p^*$ (or any pressure-type) coordinate cannot |
| 21 |
|
|
maintain the vertical resolution near the surface as the bottom topography rises above |
| 22 |
|
|
sea level. The vertical length scales near the ground are small and can vary |
| 23 |
|
|
on small time scales, and the vertical grid must be adequate to resolve them. |
| 24 |
|
|
Many studies with both regional and global atmospheric models have demonstrated the |
| 25 |
|
|
improvements in the simulations when the vertical resolution near the surface is |
| 26 |
|
|
increased (\cite{bm:99,Inn:01,wo:98,breth:99}). Some of the benefit of increased resolution |
| 27 |
|
|
near the surface is realized by employing the higher resolution for the computation of the |
| 28 |
|
|
forcing due to turbulent and convective processes in the atmosphere. |
| 29 |
|
|
|
| 30 |
|
|
The parameterizations of atmospheric subgrid scale processes are all essentially |
| 31 |
|
|
one-dimensional in nature, and the computation of the terms in the equations of |
| 32 |
|
|
motion due to these processes can be performed for the air column over one grid point |
| 33 |
|
|
at a time. The vertical grid on which these computations take place can therefore be |
| 34 |
|
|
entirely independant of the grid on which the equations of motion are integrated, and |
| 35 |
|
|
the 'tendency' terms can be interpolated to the vertical grid on which the equations |
| 36 |
|
|
of motion are integrated. A modified $p^*$ coordinate, which adjusts to the local |
| 37 |
|
|
terrain and adds additional levels between the lower levels of the existing $p^*$ grid |
| 38 |
|
|
(and perhaps between the levels near the tropopause as well), is implemented. The |
| 39 |
|
|
vertical discretization is different for each grid point, although it consist of the |
| 40 |
|
|
same number of levels. Additional 'sponge' levels aloft are added when needed. The levels |
| 41 |
|
|
of the physics grid are constrained to fit exactly into the existing $p^*$ grid, simplifying |
| 42 |
|
|
the mapping between the two vertical coordinates. This is illustrated as follows: |
| 43 |
|
|
|
| 44 |
molod |
1.1 |
\begin{figure}[htbp] |
| 45 |
|
|
\vspace*{-0.4in} |
| 46 |
|
|
\begin{center} |
| 47 |
jmc |
1.13 |
\includegraphics[height=2.4in]{s_phys_pkgs/figs/vertical.eps} |
| 48 |
edhill |
1.8 |
\caption{Vertical discretization for MITgcm (dark grey lines) and for the |
| 49 |
molod |
1.5 |
atmospheric physics (light grey lines). In this implementation, all MITgcm level |
| 50 |
|
|
interfaces must coincide with atmospheric physics level interfaces.} |
| 51 |
molod |
1.1 |
\end{center} |
| 52 |
|
|
\end{figure} |
| 53 |
|
|
|
| 54 |
molod |
1.5 |
The algorithm presented here retains the state variables on the high resolution 'physics' |
| 55 |
|
|
grid as well as on the coarser resolution 'dynamics` grid, and ensures that the two |
| 56 |
|
|
estimates of the state 'agree' on the coarse resolution grid. It would have been possible |
| 57 |
|
|
to implement a technique in which the tendencies due to atmospheric physics are computed |
| 58 |
|
|
on the high resolution grid and the state variables are retained at low resolution only. |
| 59 |
|
|
This, however, for the case of the turbulence parameterization, would mean that the |
| 60 |
|
|
turbulent kinetic energy source terms, and all the turbulence terms that are written |
| 61 |
|
|
in terms of gradients of the mean flow, cannot really be computed making use of the fine |
| 62 |
|
|
structure in the vertical. |
| 63 |
|
|
|
| 64 |
|
|
\subsubsection{Equations on Both Grids} |
| 65 |
|
|
|
| 66 |
|
|
In addition to computing the physical forcing terms of the momentum, thermodynamic and humidity |
| 67 |
|
|
equations on the modified (higher resolution) grid, the higher resolution structure of the |
| 68 |
|
|
atmosphere (the boundary layer) is retained between physics calculations. This neccessitates |
| 69 |
|
|
a second set of evolution equations for the atmospheric state variables on the modified grid. |
| 70 |
|
|
If the equation for the evolution of $U$ on $p^*$ can be expressed as: |
| 71 |
molod |
1.1 |
\[ |
| 72 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^*}^{total} = |
| 73 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^*}^{dynamics} + |
| 74 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^*}^{physics} |
| 75 |
|
|
\] |
| 76 |
molod |
1.5 |
where the physics forcing terms on $p^*$ have been mapped from the modified grid, then an additional |
| 77 |
|
|
equation to govern the evolution of $U$ (for example) on the modified grid is written: |
| 78 |
molod |
1.1 |
\[ |
| 79 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^{*m}}^{total} = |
| 80 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^{*m}}^{dynamics} + |
| 81 |
|
|
\left . {\partial U \over {\partial t}} \right |_{p^{*m}}^{physics} + |
| 82 |
|
|
\gamma ({\left . U \right |_{p^*}} - {\left . U \right |_{p^{*m}}}) |
| 83 |
|
|
\] |
| 84 |
molod |
1.5 |
where $p^{*m}$ refers to the modified higher resolution grid, and the dynamics forcing terms have |
| 85 |
|
|
been mapped from $p^*$ space. The last term on the RHS is a relaxation term, meant to constrain |
| 86 |
|
|
the state variables on the modified vertical grid to `track' the state variables on the $p^*$ grid |
| 87 |
|
|
on some time scale, governed by $\gamma$. In the present implementation, $\gamma = 1$, requiring |
| 88 |
|
|
an immediate agreement between the two 'states'. |
| 89 |
|
|
|
| 90 |
|
|
\subsubsection{Time stepping Sequence} |
| 91 |
|
|
If we write $T_{phys}$ as the temperature (or any other state variable) on the high |
| 92 |
|
|
resolution physics grid, and $T_{dyn}$ as the temperature on the coarse vertical resolution |
| 93 |
|
|
dynamics grid, then: |
| 94 |
|
|
|
| 95 |
|
|
\begin{enumerate} |
| 96 |
|
|
%\itemsep{-0.05in} |
| 97 |
|
|
|
| 98 |
|
|
\item{Compute the tendency due to physics processes.} |
| 99 |
|
|
|
| 100 |
molod |
1.6 |
\item{Advance the physics state: ${{T^{n+1}}^{**}}_{phys}(l) = {T^n}_{phys}(l) + \delta T_{phys}$.} |
| 101 |
molod |
1.5 |
|
| 102 |
|
|
\item{Interpolate the physics tendency to the dynamics grid, and advance the dynamics |
| 103 |
|
|
state by physics and dynamics tendencies: |
| 104 |
|
|
${T^{n+1}}_{dyn}(L) = {T^n}_{dyn}(L) + \delta T_{dyn}(L) + [\delta T _{phys}(l)](L)$.} |
| 105 |
|
|
|
| 106 |
|
|
\item{Interpolate the dynamics tendency to the physics grid, and update the physics |
| 107 |
|
|
grid due to dynamics tendencies: |
| 108 |
molod |
1.6 |
${{T^{n+1}}^*}_{phys}(l)$ = ${{T^{n+1}}^{**}}_{phys}(l) + {\delta T_{dyn}(L)}(l)$.} |
| 109 |
molod |
1.5 |
|
| 110 |
|
|
\item{Apply correction term to physics state to account for divergence from dynamics state: |
| 111 |
molod |
1.6 |
${T^{n+1}}_{phys}(l)$ = ${{T^{n+1}}^*}_{phys}(l) + \gamma \{ T_{dyn}(L) - [T_{phys}(l)](L) \}(l)$.} \\ |
| 112 |
molod |
1.5 |
Where $\gamma=1$ here. |
| 113 |
|
|
|
| 114 |
|
|
\end{enumerate} |
| 115 |
|
|
|
| 116 |
|
|
\subsubsection{Interpolation} |
| 117 |
|
|
In order to minimize the correction terms for the state variables on the alternative, |
| 118 |
|
|
higher resolution grid, the vertical interpolation scheme must be constructed so that |
| 119 |
|
|
a dynamics-to-physics interpolation can be exactly reversed with a physics-to-dynamics mapping. |
| 120 |
molod |
1.7 |
The simple scheme employed to achieve this is:\\ |
| 121 |
molod |
1.5 |
|
| 122 |
|
|
Coarse to fine:\ |
| 123 |
|
|
For all physics layers l in dynamics layer L, $ T_{phys}(l) = \{T_{dyn}(L)\} = T_{dyn}(L) $. |
| 124 |
|
|
|
| 125 |
|
|
Fine to coarse:\ |
| 126 |
molod |
1.7 |
For all physics layers l in dynamics layer L, $T_{dyn}(L) = [T_{phys}(l)] = \int{T_{phys} dp } $.\\ |
| 127 |
molod |
1.5 |
|
| 128 |
|
|
Where $\{\}$ is defined as the dynamics-to-physics operator and $[ ]$ is the physics-to-dynamics operator, $T$ stands for any state variable, and the subscripts $phys$ and $dyn$ stand for variables on |
| 129 |
|
|
the physics and dynamics grids, respectively. |
| 130 |
molod |
1.1 |
|
| 131 |
molod |
1.4 |
\subsubsection {Key subroutines, parameters and files } |
| 132 |
molod |
1.1 |
|
| 133 |
molod |
1.7 |
\noindent |
| 134 |
|
|
One of the central elements of the gridalt package is the routine which |
| 135 |
|
|
is called from subroutine gridalt\_initialise to define the grid to be |
| 136 |
|
|
used for the high end physics calculations. Routine make\_phys\_grid |
| 137 |
|
|
passes back the parameters which define the grid, ultimately stored |
| 138 |
|
|
in the common block gridalt\_mapping. |
| 139 |
|
|
|
| 140 |
|
|
\begin{verbatim} |
| 141 |
|
|
subroutine make_phys_grid(drF,hfacC,im1,im2,jm1,jm2,Nr, |
| 142 |
|
|
. Nsx,Nsy,i1,i2,j1,j2,bi,bj,Nrphys,Lbot,dpphys,numlevphys,nlperdyn) |
| 143 |
|
|
c*********************************************************************** |
| 144 |
|
|
c Purpose: Define the grid that the will be used to run the high-end |
| 145 |
|
|
c atmospheric physics. |
| 146 |
|
|
c |
| 147 |
|
|
c Algorithm: Fit additional levels of some (~) known thickness in |
| 148 |
|
|
c between existing levels of the grid used for the dynamics |
| 149 |
|
|
c |
| 150 |
|
|
c Need: Information about the dynamics grid vertical spacing |
| 151 |
|
|
c |
| 152 |
|
|
c Input: drF - delta r (p*) edge-to-edge |
| 153 |
|
|
c hfacC - fraction of grid box above topography |
| 154 |
|
|
c im1, im2 - beginning and ending i - dimensions |
| 155 |
|
|
c jm1, jm2 - beginning and ending j - dimensions |
| 156 |
|
|
c Nr - number of levels in dynamics grid |
| 157 |
|
|
c Nsx,Nsy - number of processes in x and y direction |
| 158 |
|
|
c i1, i2 - beginning and ending i - index to fill |
| 159 |
|
|
c j1, j2 - beginning and ending j - index to fill |
| 160 |
|
|
c bi, bj - x-dir and y-dir index of process |
| 161 |
|
|
c Nrphys - number of levels in physics grid |
| 162 |
|
|
c |
| 163 |
|
|
c Output: dpphys - delta r (p*) edge-to-edge of physics grid |
| 164 |
|
|
c numlevphys - number of levels used in the physics |
| 165 |
|
|
c nlperdyn - physics level number atop each dynamics layer |
| 166 |
|
|
c |
| 167 |
|
|
c NOTES: 1) Pressure levs are built up from bottom, using p0, ps and dp: |
| 168 |
|
|
c p(i,j,k)=p(i,j,k-1) + dp(k)*ps(i,j)/p0(i,j) |
| 169 |
|
|
c 2) Output dp's are aligned to fit EXACTLY between existing |
| 170 |
|
|
c levels of the dynamics vertical grid |
| 171 |
|
|
c 3) IMPORTANT! This routine assumes the levels are numbered |
| 172 |
|
|
c from the bottom up, ie, level 1 is the surface. |
| 173 |
|
|
c IT WILL NOT WORK OTHERWISE!!! |
| 174 |
|
|
c 4) This routine does NOT work for surface pressures less |
| 175 |
|
|
c (ie, above in the atmosphere) than about 350 mb |
| 176 |
|
|
c*********************************************************************** |
| 177 |
|
|
\end{verbatim} |
| 178 |
|
|
|
| 179 |
|
|
\noindent In the case of the grid used to compute the atmospheric physical |
| 180 |
|
|
forcing (fizhi package), the locations of the grid points move in time with |
| 181 |
|
|
the MITgcm $p^*$ coordinate, and subroutine gridalt\_update is called during |
| 182 |
|
|
the run to update the locations of the grid points: |
| 183 |
|
|
|
| 184 |
|
|
\begin{verbatim} |
| 185 |
|
|
subroutine gridalt_update(myThid) |
| 186 |
|
|
c*********************************************************************** |
| 187 |
|
|
c Purpose: Update the pressure thicknesses of the layers of the |
| 188 |
|
|
c alternative vertical grid (used now for atmospheric physics). |
| 189 |
|
|
c |
| 190 |
|
|
c Calculate: dpphys - new delta r (p*) edge-to-edge of physics grid |
| 191 |
|
|
c using dpphys0 (initial value) and rstarfacC |
| 192 |
|
|
c*********************************************************************** |
| 193 |
|
|
\end{verbatim} |
| 194 |
|
|
|
| 195 |
|
|
\noindent The gridalt package also supplies utility routines which perform |
| 196 |
|
|
the mappings from one grid to the other. These routines are called from the |
| 197 |
|
|
code which computes the fields on the alternative (fizhi) grid. |
| 198 |
|
|
|
| 199 |
|
|
\begin{verbatim} |
| 200 |
|
|
subroutine dyn2phys(qdyn,pedyn,im1,im2,jm1,jm2,lmdyn,Nsx,Nsy, |
| 201 |
|
|
. idim1,idim2,jdim1,jdim2,bi,bj,windphy,pephy,Lbot,lmphy,nlperdyn, |
| 202 |
|
|
. flg,qphy) |
| 203 |
|
|
C*********************************************************************** |
| 204 |
|
|
C Purpose: |
| 205 |
|
|
C To interpolate an arbitrary quantity from the 'dynamics' eta (pstar) |
| 206 |
|
|
C grid to the higher resolution physics grid |
| 207 |
|
|
C Algorithm: |
| 208 |
|
|
C Routine works one layer (edge to edge pressure) at a time. |
| 209 |
|
|
C Dynamics -> Physics retains the dynamics layer mean value, |
| 210 |
|
|
C weights the field either with the profile of the physics grid |
| 211 |
|
|
C wind speed (for U and V fields), or uniformly (T and Q) |
| 212 |
|
|
C |
| 213 |
|
|
C Input: |
| 214 |
|
|
C qdyn..... [im,jm,lmdyn] Arbitrary Quantity on Input Grid |
| 215 |
|
|
C pedyn.... [im,jm,lmdyn+1] Pressures at bottom edges of input levels |
| 216 |
|
|
C im1,2 ... Limits for Longitude Dimension of Input |
| 217 |
|
|
C jm1,2 ... Limits for Latitude Dimension of Input |
| 218 |
|
|
C lmdyn.... Vertical Dimension of Input |
| 219 |
|
|
C Nsx...... Number of processes in x-direction |
| 220 |
|
|
C Nsy...... Number of processes in y-direction |
| 221 |
|
|
C idim1,2.. Beginning and ending i-values to calculate |
| 222 |
|
|
C jdim1,2.. Beginning and ending j-values to calculate |
| 223 |
|
|
C bi....... Index of process number in x-direction |
| 224 |
|
|
C bj....... Index of process number in x-direction |
| 225 |
|
|
C windphy.. [im,jm,lmphy] Magnitude of the wind on the output levels |
| 226 |
|
|
C pephy.... [im,jm,lmphy+1] Pressures at bottom edges of output levels |
| 227 |
|
|
C lmphy.... Vertical Dimension of Output |
| 228 |
|
|
C nlperdyn. [im,jm,lmdyn] Highest Physics level in each dynamics level |
| 229 |
|
|
C flg...... Flag to indicate field type (0 for T or Q, 1 for U or V) |
| 230 |
|
|
C |
| 231 |
|
|
C Output: |
| 232 |
|
|
C qphy..... [im,jm,lmphy] Quantity at output grid (physics grid) |
| 233 |
|
|
C |
| 234 |
|
|
C Notes: |
| 235 |
|
|
C 1) This algorithm assumes that the output (physics) grid levels |
| 236 |
|
|
C fit exactly into the input (dynamics) grid levels |
| 237 |
|
|
C*********************************************************************** |
| 238 |
|
|
\end{verbatim} |
| 239 |
|
|
|
| 240 |
|
|
\noindent And similarly, gridalt contains subroutine phys2dyn. |
| 241 |
|
|
|
| 242 |
molod |
1.9 |
\subsubsection {Gridalt Diagnostics} |
| 243 |
|
|
\label{sec:pkg:gridalt:diagnostics} |
| 244 |
|
|
|
| 245 |
edhill |
1.10 |
{\footnotesize |
| 246 |
molod |
1.9 |
\begin{verbatim} |
| 247 |
|
|
|
| 248 |
|
|
------------------------------------------------------------------------ |
| 249 |
|
|
<-Name->|Levs|<-parsing code->|<-- Units -->|<- Tile (max=80c) |
| 250 |
|
|
------------------------------------------------------------------------ |
| 251 |
|
|
DPPHYS | 20 |SM ML |Pascal |Pressure Thickness of Layers on Fizhi Grid |
| 252 |
|
|
\end{verbatim} |
| 253 |
edhill |
1.10 |
} |
| 254 |
molod |
1.9 |
|
| 255 |
molod |
1.4 |
\subsubsection {Dos and donts} |
| 256 |
molod |
1.1 |
|
| 257 |
molod |
1.4 |
\subsubsection {Gridalt Reference} |
| 258 |
molod |
1.11 |
|
| 259 |
|
|
\subsubsection{Experiments and tutorials that use gridalt} |
| 260 |
|
|
\label{sec:pkg:gridalt:experiments} |
| 261 |
|
|
|
| 262 |
|
|
\begin{itemize} |
| 263 |
|
|
\item{Fizhi experiment, in fizhi-cs-32x32x10 verification directory } |
| 264 |
|
|
\end{itemize} |
Parent Directory
| 
Revision Log
| 
Revision Graph