40 |
C in the middle of an integration. |
C in the middle of an integration. |
41 |
#undef SEAICE_MULTICATEGORY |
#undef SEAICE_MULTICATEGORY |
42 |
|
|
|
C-- By default for B-grid dynamics solver wind stress under sea-ice is |
|
|
C set to the same value as it would be if there was no sea-ice. |
|
|
C Define following CPP flag for B-grid ice-ocean stress coupling. |
|
|
#undef SEAICE_TEST_ICE_STRESS_1 |
|
|
|
|
|
C-- By default for B-grid dynamics solver surface tilt is obtained |
|
|
C indirectly via geostrophic velocities. Define following CPP |
|
|
C in order to ues ETAN instead. |
|
|
#undef EXPLICIT_SSH_SLOPE |
|
|
|
|
43 |
C-- By default the freezing point of water is set to the value of |
C-- By default the freezing point of water is set to the value of |
44 |
C the parameter SEAICE_freeze (=-1.96 by default). To use a |
C the parameter SEAICE_freeze (=-1.96 by default). To use a |
45 |
C simple linear dependence of the freezing point on salinity, |
C simple linear dependence of the freezing point on salinity, |
55 |
#define SEAICE_SALINITY |
#define SEAICE_SALINITY |
56 |
|
|
57 |
C-- Track sea ice age. |
C-- Track sea ice age. |
58 |
|
C By default sea ice age is associated with ice area. |
59 |
|
C Define SEAICE_AGE_VOL to associate age with volume. |
60 |
#define SEAICE_AGE |
#define SEAICE_AGE |
61 |
|
#ifdef SEAICE_AGE |
62 |
|
# define SEAICE_AGE_VOL |
63 |
|
#endif |
64 |
|
|
65 |
C-- By default the seaice model is discretized on a B-Grid (for |
C-- By default the seaice model is discretized on a B-Grid (for |
66 |
C historical reasons). Define the following flag to use a new |
C historical reasons). Define the following flag to use a new |
70 |
C-- Only for the C-grid version it is possible to |
C-- Only for the C-grid version it is possible to |
71 |
#ifdef SEAICE_CGRID |
#ifdef SEAICE_CGRID |
72 |
C enable EVP code by defining the following flag |
C enable EVP code by defining the following flag |
73 |
#define SEAICE_ALLOW_EVP |
# define SEAICE_ALLOW_EVP |
74 |
#ifdef SEAICE_ALLOW_EVP |
# ifdef SEAICE_ALLOW_EVP |
75 |
C-- When set use SEAICE_zetaMin and SEAICE_evpDampC to limit |
C-- When set use SEAICE_zetaMin and SEAICE_evpDampC to limit |
76 |
C-- viscosities from below and above in seaice_evp |
C-- viscosities from below and above in seaice_evp |
77 |
C-- not necessary, and not recommended, but used here for backward |
C-- not necessary, and not recommended, but used here for backward |
78 |
C-- compatibility |
C-- compatibility |
79 |
#define SEAICE_ALLOW_CLIPZETA |
# define SEAICE_ALLOW_CLIPZETA |
80 |
#endif /* SEAICE_ALLOW_EVP */ |
# endif /* SEAICE_ALLOW_EVP */ |
81 |
C allow the truncated ellipse rheology (runtime flag SEAICEuseTEM) |
C allow the truncated ellipse rheology (runtime flag SEAICEuseTEM) |
82 |
#undef SEAICE_ALLOW_TEM |
# undef SEAICE_ALLOW_TEM |
83 |
|
#else /* not SEAICE_CGRID, but old B-grid */ |
84 |
|
C-- By default for B-grid dynamics solver wind stress under sea-ice is |
85 |
|
C set to the same value as it would be if there was no sea-ice. |
86 |
|
C Define following CPP flag for B-grid ice-ocean stress coupling. |
87 |
|
# define SEAICE_BICE_STRESS |
88 |
|
|
89 |
|
C-- By default for B-grid dynamics solver surface tilt is obtained |
90 |
|
C indirectly via geostrophic velocities. Define following CPP |
91 |
|
C in order to use ETAN instead. |
92 |
|
# define EXPLICIT_SSH_SLOPE |
93 |
#endif /* SEAICE_CGRID */ |
#endif /* SEAICE_CGRID */ |
94 |
|
|
95 |
C-- When set use MAX_HEFF to cap sea ice thickness in seaice_growth |
C-- When set use MAX_HEFF to cap sea ice thickness in seaice_growth |