4 |
Notes on tags used in MITgcmUV |
Notes on tags used in MITgcmUV |
5 |
============================== |
============================== |
6 |
|
|
7 |
|
o optim/optim_readdata.F: |
8 |
|
- add some output about obcs variables that might help debugging |
9 |
|
- add a check about nvarlength |
10 |
|
o pkg/ctrl: once again, fix computation of endrec in s/r ctrl_init_rec |
11 |
|
o pkg/diagnostics (velocity potential): |
12 |
|
- fix mask for OBCS (still problems in stream-function with OBCS); |
13 |
|
- add specific parameter (default = main code CG2D params) for solver; |
14 |
|
- in case of poor convergence, use solution corresponding to lowest residual. |
15 |
|
o pkg/seaice/seaice_growth.F: small changes that permit vectorizable |
16 |
|
adjoint code. In general statements like tmpscal=fld(i,j) are problematic |
17 |
|
and should be avoided where possible. |
18 |
|
o model/src (rStar): |
19 |
|
- include r* effect on reference-state (PhiRef) in totPhiHyd |
20 |
|
(so that it's really the potential anomaly at the cell center); |
21 |
|
affect solution only if z* with full pressure in EOS. |
22 |
|
- test-exp global_ocean.90x40x15: reduce viscA4 (was not stable) and |
23 |
|
update output (because of z* in totPhiHyd and viscA4 changes); |
24 |
|
- keep the previous diagnostics as "PHIHYDcR" (closer to potential anomaly |
25 |
|
@ constant r) until interpolation at constant r is implemented. |
26 |
|
o pkg/diagnostics |
27 |
|
- fix RCENTER diagnostics in case cell center is not at interface middle |
28 |
|
o add code for TEOS-10 (www.teos-10.org, McDougall et al. 2011). Use |
29 |
|
this eos with eosType = 'TEOS10', in data (PARM01). This eos implies |
30 |
|
that THETA and SALT are "conservative temperature" and "absolute |
31 |
|
salinity" |
32 |
|
o pkg/ctrl |
33 |
|
- fix computation of endrec in s/r ctrl_init_rec |
34 |
|
- ctrl_pack/unpack_*: remove unused variables and some obsolete code |
35 |
|
o pkg/seaice/seaice_growth.F |
36 |
|
- fix recomputation with FENTY_AREA_EXPANSION_CONTRACTION code, |
37 |
|
remove then obsolete STORE directives |
38 |
|
- fix STORE directives for tice and tices, so that only the |
39 |
|
appropriate part of the fields are stored (and not the entire |
40 |
|
field); update global_ocean.cs32x15.seaice AD output. |
41 |
|
- cosmetic changes: adjust CPP flags and indentation for better |
42 |
|
legibilty |
43 |
|
o pkg/autodiff: add mnc-output of adBottomDragFld (code contributed by |
44 |
|
Chris Wilson) |
45 |
|
o pkg/gmredi: |
46 |
|
Add Sub-Meso Eddies parameterisation from Baylor (for now, disabled with TAF), |
47 |
|
and test it in verification exp. "front_relax.bvp" (update output.bvp.txt) |
48 |
|
|
49 |
|
checkpoint63 (2011/07/11) |
50 |
|
o pkg/exch2: |
51 |
|
- rename+move: nTiles in W2_EXCH2_PARAMS.h --> exch2_nTiles in W2_EXCH2_TOPOLOGY.h |
52 |
|
- exch2 version of Cumul-Sum routine: S/R W2_SET_MAP_CUMSUM set up the |
53 |
|
(2*nTiles)x(nTiles) Cumul-Sum matrix and Master Proc collects all tiles X,Y |
54 |
|
increments, calculates Cumul-Sum @ tile origin and sends results to each tile. |
55 |
o pkg/diagnostics: |
o pkg/diagnostics: |
56 |
- deal with pairs of post-processed diags which are computed together; in |
- deal with pairs of post-processed diags which are computed together; in |
57 |
particular, re-order list of diags within 1 file to save 2nd computation. |
particular, re-order list of diags within 1 file to save 2nd computation. |
58 |
- add S/R to compute velocity stream-function (called after velocity-potential |
- add S/R to compute velocity stream-function (called after velocity-potential |
59 |
calculation) from divergence free transport -> new diagnostics "PsiVEL". |
calculation) from divergence free transport -> new diagnostics "PsiVEL". |
60 |
|
- add parameter to select grid-point location where PsiVEL == 0. |
61 |
o eesupp/src: |
o eesupp/src: |
62 |
new S/R to calculate cumulated sum on tiled array, corner grid-cell location |
new S/R to calculate cumulated sum on tiled array, corner grid-cell location |
63 |
(specific S/R needed with exch2 topology - for now, just print an error msg) |
(specific S/R needed with exch2 topology - for now, just print an error msg) |