4 |
Notes on tags used in MITgcmUV |
Notes on tags used in MITgcmUV |
5 |
============================== |
============================== |
6 |
|
|
7 |
|
o store 3-D (in-situ) density in commom block (DYNVARS.h) |
8 |
|
- save 1 rho computation. |
9 |
|
- no longer modify T & S inland when using down_slope pkg. |
10 |
|
o gad_som : allow to switch to SOM advection for T & S without corresponding |
11 |
|
pickup files (using new S/R: MDS_CHECK4FILE). |
12 |
|
o keep removing _BEGIN/_END_MASTER between MDSIO S/R call |
13 |
|
(for useSingleCpuIO to work in multi-threaded) |
14 |
|
o pkg/shelfice: |
15 |
|
- disentangle parameters: retire shelfIceFile in data/PARM05 and substitute |
16 |
|
with SHELFICEtopoFile in data.shelfice |
17 |
|
- move code for reading ice shelf topography and modifying hFacC into separate |
18 |
|
subroutines of the shelfice package |
19 |
|
- separate initialisation of "fixed" and "variable" variables |
20 |
|
- kTopC is not (yet) replaced by kSurfC, although this is possible |
21 |
|
o fix broken diagnostic SIatmFW and changed the units from m/s to kg/m^2/s |
22 |
|
o add initialisation of deepFac if using Pcoords (new S/R set_grid_factors) |
23 |
|
and rename: |
24 |
|
ini_phiref.F --> set_ref_state.F (+ set anelastic factors) |
25 |
|
ini_reference_state.F --> load_ref_files.F (- set anelastic factors) |
26 |
|
o change FIND_RHO_SCALAR : return rho (instead of rho - rhoConst) |
27 |
|
|
28 |
|
checkpoint61c |
29 |
|
o add option ALLOW_ADDFLUID and run-time selector "selectAddFluid" |
30 |
|
to add mass source/sink of fluid in the interior (3-D generalisation |
31 |
|
of oceanic real-fresh water flux). |
32 |
|
o pkg/monitor: fix recip_dr argument in mon_advcflw2 call (-> advcfl_W_hf_max) |
33 |
|
o vermix test experiment: switch from LINEAR EOS to MDJWF (not tested before) |
34 |
|
o new pkg: down_slope |
35 |
|
density-driven downsloping flow parameterisation (Tellus, 1999, 412-430). |
36 |
|
- presently, modify T & S inland (dwnslp_calc_rho.F). |
37 |
|
can be avoided if rho was stored in common bloc and used in calc_phi_hyd. |
38 |
|
- implementation for ocean in P-coords not tested. |
39 |
|
- add secondary test to global_ocean.90x40x15 (input.dwnslp) to check this pkg. |
40 |
|
o move kSurfC,kSurfW & kSurfS from SURFACE.h to GRID.h (next to kLowC) |
41 |
|
(to facilitate conversion of oceanic pkg to p-coordinate). |
42 |
|
o change FIND_RHO to FIND_RHO_2D : |
43 |
|
pass arguments tFld & sFld as local (tile) 2D-arrays ; +fix EOS_CHECK. |
44 |
|
o new pkg: cheapaml |
45 |
|
|
46 |
|
checkpoint61b |
47 |
|
o exch2: |
48 |
|
change index bounds in rx2_cube exchanges (new S/R: EXCH2_GET_UV_BOUNDS) |
49 |
|
- no longer depend on the order sequence (N,S,E,W). |
50 |
|
- 3rd exchange no longer needed (tested with 24 tiles). |
51 |
|
- same modif to hand-written adjoint S/R (global_ocean.cs32x15: zero diff) |
52 |
|
- exch_UV_A-grid readily available (but not yet tested). |
53 |
|
comment out 3rd exch call and remove copy of V to U at SE & NE face-corners |
54 |
|
(both are no longer needed) in exch_uv: no effect in forward run; but |
55 |
|
get truncation error differences with adjoint exch. |
56 |
|
o exch2: |
57 |
|
- change index-bounds storage (moved from target to local tile, |
58 |
|
more intuitive this way) ; rename/remove some variables. |
59 |
|
- change utils/exch2/matlab-topology-generator & code_mods accordingly. |
60 |
|
|
61 |
|
checkpoint61a |
62 |
|
o exch2/matlab-topology-generator: |
63 |
|
fix bug in index bounds for N-S internal exchange (hard to tell if this |
64 |
|
had any effect on the solution). |
65 |
o pkg/mnc: small fix in mnc_handle_err: make sure that length of msgbuf |
o pkg/mnc: small fix in mnc_handle_err: make sure that length of msgbuf |
66 |
is exceeded |
is exceeded |
67 |
o testreport: modify syntax of awk, so that it works also with |
o testreport: modify syntax of awk, so that it works also with |