| 4 |
Notes on tags used in MITgcmUV |
Notes on tags used in MITgcmUV |
| 5 |
============================== |
============================== |
| 6 |
|
|
| 7 |
|
o fix a bug in diagnostic SIatmFW and changed the units from m/s to kg/m^2/s |
| 8 |
|
o add initialisation of deepFac if using Pcoords (new S/R set_grid_factors) |
| 9 |
|
and rename: |
| 10 |
|
ini_phiref.F --> set_ref_state.F (+ set anelastic factors) |
| 11 |
|
ini_reference_state.F --> load_ref_files.F (- set anelastic factors) |
| 12 |
|
o change FIND_RHO_SCALAR : return rho (instead of rho - rhoConst) |
| 13 |
|
|
| 14 |
|
checkpoint61c |
| 15 |
|
o add option ALLOW_ADDFLUID and run-time selector "selectAddFluid" |
| 16 |
|
to add mass source/sink of fluid in the interior (3-D generalisation |
| 17 |
|
of oceanic real-fresh water flux). |
| 18 |
|
o pkg/monitor: fix recip_dr argument in mon_advcflw2 call (-> advcfl_W_hf_max) |
| 19 |
|
o vermix test experiment: switch from LINEAR EOS to MDJWF (not tested before) |
| 20 |
|
o new pkg: down_slope |
| 21 |
|
density-driven downsloping flow parameterisation (Tellus, 1999, 412-430). |
| 22 |
|
- presently, modify T & S inland (dwnslp_calc_rho.F). |
| 23 |
|
can be avoided if rho was stored in common bloc and used in calc_phi_hyd. |
| 24 |
|
- implementation for ocean in P-coords not tested. |
| 25 |
|
- add secondary test to global_ocean.90x40x15 (input.dwnslp) to check this pkg. |
| 26 |
|
o move kSurfC,kSurfW & kSurfS from SURFACE.h to GRID.h (next to kLowC) |
| 27 |
|
(to facilitate conversion of oceanic pkg to p-coordinate). |
| 28 |
|
o change FIND_RHO to FIND_RHO_2D : |
| 29 |
|
pass arguments tFld & sFld as local (tile) 2D-arrays ; +fix EOS_CHECK. |
| 30 |
|
o new pkg: cheapaml |
| 31 |
|
|
| 32 |
|
checkpoint61b |
| 33 |
|
o exch2: |
| 34 |
|
change index bounds in rx2_cube exchanges (new S/R: EXCH2_GET_UV_BOUNDS) |
| 35 |
|
- no longer depend on the order sequence (N,S,E,W). |
| 36 |
|
- 3rd exchange no longer needed (tested with 24 tiles). |
| 37 |
|
- same modif to hand-written adjoint S/R (global_ocean.cs32x15: zero diff) |
| 38 |
|
- exch_UV_A-grid readily available (but not yet tested). |
| 39 |
|
comment out 3rd exch call and remove copy of V to U at SE & NE face-corners |
| 40 |
|
(both are no longer needed) in exch_uv: no effect in forward run; but |
| 41 |
|
get truncation error differences with adjoint exch. |
| 42 |
|
o exch2: |
| 43 |
|
- change index-bounds storage (moved from target to local tile, |
| 44 |
|
more intuitive this way) ; rename/remove some variables. |
| 45 |
|
- change utils/exch2/matlab-topology-generator & code_mods accordingly. |
| 46 |
|
|
| 47 |
|
checkpoint61a |
| 48 |
|
o exch2/matlab-topology-generator: |
| 49 |
|
fix bug in index bounds for N-S internal exchange (hard to tell if this |
| 50 |
|
had any effect on the solution). |
| 51 |
|
o pkg/mnc: small fix in mnc_handle_err: make sure that length of msgbuf |
| 52 |
|
is exceeded |
| 53 |
|
o testreport: modify syntax of awk, so that it works also with |
| 54 |
|
awk, and not only with nawk and gawk |
| 55 |
|
|
| 56 |
|
checkpoint61 |
| 57 |
o autodiff |
o autodiff |
| 58 |
Change default for TAF usage by removing argument '-nonew_arg' |
Change default for TAF usage by removing argument '-nonew_arg' |
| 59 |
This changes TAF subroutine argument list (ordering of active var.) |
This changes TAF subroutine argument list (ordering of active var.) |
Parent Directory
| 
Revision Log
| 
Revision Graph
| 
Patch