3 |
Notes on tags used in MITgcmUV |
Notes on tags used in MITgcmUV |
4 |
============================== |
============================== |
5 |
|
|
6 |
checkpoint47d_post |
o S/R aim_initialise.F replace S/R aim_init from file aim_do_inphys.F: |
7 |
|
- read AIM physics parameters from a file (data.aimphys) |
8 |
|
- set defaults values = F.Molteni paper (Clim.Dyn., 2002) |
9 |
|
|
10 |
|
checkpoint46j_post |
11 |
|
o split calc_exact_eta in 2 S/R : integr_continuity & update_etaH |
12 |
|
o move wVel computation at the end of the time step, in S/R integr_continuity |
13 |
|
o create specific S/R to exchange T,S before DYNAMICS (for stagger time step) |
14 |
|
o update timeave pkg for wVel diagnostic. |
15 |
|
checkpoint46j_pre |
16 |
|
|
17 |
|
checkpoint46i_post |
18 |
|
o Clean up AIM package (and keep the results unchanged): |
19 |
|
include CPP_OPTION and use IMPLICT NONE in all routines ; |
20 |
|
declare all the variables _RL ; use _d 0 for all numerical constants. |
21 |
|
use ifdef ALLOW_AIM everywhere. And now AIM can be used with g77 ! |
22 |
|
|
23 |
|
checkpoint46h_post |
24 |
|
o cleaned up the use of rhoNil and rhoConst. |
25 |
|
- rhoNil should only appear in the LINEAR equation of state, everywhere |
26 |
|
else rhoNil is replaced by rhoConst, e.g. find_rho computes rho-rhoConst |
27 |
|
and the dynamical equations are all divided by rhoConst |
28 |
|
o introduced new parameter rhoConstFresh, a reference density of fresh |
29 |
|
water, to remove the fresh water flux's dependence on rhoNil. The default |
30 |
|
value is 999.8 kg/m^3 |
31 |
|
o cleanup up external_forcing.F and external_forcing_surf.F |
32 |
|
- can now be used by both OCEANIC and OCEANICP |
33 |
|
checkpoint46h_pre |
34 |
|
|
35 |
|
Added code to convert surface volume flux (fresh water) into |
36 |
|
a mass flux when using P coordinates in the ocean (OCEANICP). |
37 |
|
Note: It assumes you have set rho0=rhoConst=density of fresh water. |
38 |
|
|
39 |
|
checkpoint46g_post |
40 |
|
o Include a new diagnostic variable phiHydLow for the ocean model |
41 |
|
- in z-coordinates, it is the bottom pressure anomaly |
42 |
|
- in p-coordinates, it is the sea surface elevation |
43 |
|
- in both cases, these variable have global drift, reflecting the mass |
44 |
|
drift in z-coordinates and the volume drift in p-coordinates |
45 |
|
- included time averaging for phiHydLow, be aware of the drift! |
46 |
|
o depth-dependent computation of Bo_surf for pressure coordinates |
47 |
|
in the ocean (buoyancyRelation='OCEANICP') |
48 |
|
- requires a new routine (FIND_RHO_SCALAR) to compute density with only |
49 |
|
Theta, Salinity, and Pressure in the parameter list. This routine is |
50 |
|
presently contained in find_rho.F. This routine does not give the |
51 |
|
correct density for 'POLY3', which would be a z-dependent reference |
52 |
|
density. |
53 |
|
o cleaned up find_rho |
54 |
|
- removed obsolete 'eqn' from the parameter list. |
55 |
|
o added two new verification experiments: gop and goz |
56 |
|
(4x4 degree global ocean, 15 layers in pressure and height coordinates) |
57 |
|
checkpoint46g_pre |
58 |
|
|
59 |
|
checkpoint46f_post |
60 |
|
o Enable tangent linear (forward mode) gradient checks: |
61 |
|
- extended active file handling to g_... files |
62 |
|
- added TANGENT_SIMULATION to theSimulationMode |
63 |
|
- extended grdchk package accordingly |
64 |
|
o added tangent linear setup in verification/carbon/code_ftl |
65 |
|
o added adjoint setup in verification/front_relax/code_ad |
66 |
|
|
67 |
|
checkpoint46e_post |
68 |
o Added new equation of state -> MDJWF |
o Added new equation of state -> MDJWF |
69 |
- EOS of McDougall et al., 2002, JAOT, submitted |
- EOS of McDougall et al., 2002, JAOT, submitted |
70 |
- caveat: the equation of state is only valid for a smaller (more |
- caveat: the equation of state is only valid for a smaller (more |
73 |
- added more check values for density in check_eos (ini_eos.F), some of |
- added more check values for density in check_eos (ini_eos.F), some of |
74 |
the old check values are out of the range of the MDJWF-eos, so don't |
the old check values are out of the range of the MDJWF-eos, so don't |
75 |
expect perfect matches for those |
expect perfect matches for those |
76 |
checkpoint47d_pre |
checkpoint46e_pre |
77 |
|
|
78 |
checkpoint46d_post |
checkpoint46d_post |
79 |
o fixed store_pressure to work with both buoyancy relation = 'OCEANIC' and |
o fixed store_pressure to work with both buoyancy relation = 'OCEANIC' and |